mirror of
https://github.com/SebastianWendel/nixpkgs.git
synced 2024-11-06 18:26:45 +01:00
8d925cc8db
This may be helpful to new module developers, curious users, and people who just need a reference without having to look at the implementation
54 lines
2.7 KiB
Markdown
54 lines
2.7 KiB
Markdown
# What happens during a system switch? {#sec-switching-systems}
|
|
|
|
Running `nixos-rebuild switch` is one of the more common tasks under NixOS.
|
|
This chapter explains some of the internals of this command to make it simpler
|
|
for new module developers to configure their units correctly and to make it
|
|
easier to understand what is happening and why for curious administrators.
|
|
|
|
`nixos-rebuild`, like many deployment solutions, calls `switch-to-configuration`
|
|
which resides in a NixOS system at `$out/bin/switch-to-configuration`. The
|
|
script is called with the action that is to be performed like `switch`, `test`,
|
|
`boot`. There is also the `dry-activate` action which does not really perform
|
|
the actions but rather prints what it would do if you called it with `test`.
|
|
This feature can be used to check what service states would be changed if the
|
|
configuration was switched to.
|
|
|
|
If the action is `switch` or `boot`, the bootloader is updated first so the
|
|
configuration will be the next one to boot. Unless `NIXOS_NO_SYNC` is set to
|
|
`1`, `/nix/store` is synced to disk.
|
|
|
|
If the action is `switch` or `test`, the currently running system is inspected
|
|
and the actions to switch to the new system are calculated. This process takes
|
|
two data sources into account: `/etc/fstab` and the current systemd status.
|
|
Mounts and swaps are read from `/etc/fstab` and the corresponding actions are
|
|
generated. If a new mount is added, for example, the proper `.mount` unit is
|
|
marked to be started. The current systemd state is inspected, the difference
|
|
between the current system and the desired configuration is calculated and
|
|
actions are generated to get to this state. There are a lot of nuances that can
|
|
be controlled by the units which are explained here.
|
|
|
|
After calculating what should be done, the actions are carried out. The order
|
|
of actions is always the same:
|
|
- Stop units (`systemctl stop`)
|
|
- Run activation script (`$out/activate`)
|
|
- See if the activation script requested more units to restart
|
|
- Restart systemd if needed (`systemd daemon-reexec`)
|
|
- Forget about the failed state of units (`systemctl reset-failed`)
|
|
- Reload systemd (`systemctl daemon-reload`)
|
|
- Reload systemd user instances (`systemctl --user daemon-reload`)
|
|
- Set up tmpfiles (`systemd-tmpfiles --create`)
|
|
- Reload units (`systemctl reload`)
|
|
- Restart units (`systemctl restart`)
|
|
- Start units (`systemctl start`)
|
|
- Inspect what changed during these actions and print units that failed and
|
|
that were newly started
|
|
|
|
Most of these actions are either self-explaining but some of them have to do
|
|
with our units or the activation script. For this reason, these topics are
|
|
explained in the next sections.
|
|
|
|
```{=docbook}
|
|
<xi:include href="unit-handling.section.xml" />
|
|
<xi:include href="activation-script.section.xml" />
|
|
```
|